Advanced Techniques
After becoming familiar with the proper application procedures, you’re ready to move on to advanced techniques. Please do not hesitate to reach out to our support team if you have any questions.
Embedding Pictures: Objects such as pictures, articles, and maps may be embedded in this product. The paper must be laminated or sealed with spray on clear coat otherwise the epoxy will absorb into the paper. Once the paper is properly sealed, they can be placed on your project surface. You should wait 30 minutes after applying your seal coat of epoxy before placing the objects. Subsequent flood coats will then cover and embed these objects.
Embedding Solid Objects: Wood, rocks, shells, bottle caps, coins, etc. may be embedded in this product also. All porous objects must be sealed first with the epoxy. If the objects are not sealed correctly, they will release tiny air bubbles which will form around the object during the flood coats. Placement of these objects may be done before you apply the first seal coat or they can be placed into a previously applied seal coat which has been allowed to sit for 30 minutes. Lightweight items such as bottle caps should be glued down to prevent floating.
Embedding Fragile Objects: To embed fragile items specials steps need to be taken. Using a sprayable polyurethane or lacquer clear coat is a great way to seal your object without touching it. Make sure you follow the directions for the sealer and ensure the object is fully cured before coming in contact with the epoxy.
Thick Build-Ups: This product can be used to build up unlimited depths. Each flood coat should not exceed 1/8”. Attempting to pour thicker can cause the epoxy to generate excessive heat which in turn will cause more air bubbles, possibly cracking and shrinkage. It is advisable to wait at least 4 hours between pours to allow sufficient curing and cooling.
Damming The Edges: We recommend allowing the epoxy to run over the edges of your surface as it will self-level at approximately 1/8” at a time. If your application calls for a temporary dam to be constructed, it must be done with great care to guarantee it can be removed after the epoxy is cured. Ideally, a smooth, soft or flexible plastic strip should be used because the epoxy will not stick to it. Alternatively, wooden trim can be used but only if it is first covered with a 2 to 4 mil plastic sheeting. Lining the wood trim with the plastic and tacking it to the edge should prevent the epoxy from running in between the edge and the plastic. Testing on a small mock-up should be done to ensure no leakage or problems will occur with your damming technique.
*Some very aged and kiln dried woods may need multiple seal coats to prevent air from escaping them. It is not uncommon for as many as 3 seal coats to be used on aged and kiln dried woods.
*If at any time you need help with advanced techniques, please reach out to us directly. We are always here to help
After becoming familiar with the proper application procedures, you’re ready to move on to advanced techniques. Please do not hesitate to reach out to our support team if you have any questions.
Embedding Pictures: Objects such as pictures, articles, and maps may be embedded in this product. The paper must be laminated or sealed with spray on clear coat otherwise the epoxy will absorb into the paper. Once the paper is properly sealed, they can be placed on your project surface. You should wait 30 minutes after applying your seal coat of epoxy before placing the objects. Subsequent flood coats will then cover and embed these objects.
Embedding Solid Objects: Wood, rocks, shells, bottle caps, coins, etc. may be embedded in this product also. All porous objects must be sealed first with the epoxy. If the objects are not sealed correctly, they will release tiny air bubbles which will form around the object during the flood coats. Placement of these objects may be done before you apply the first seal coat or they can be placed into a previously applied seal coat which has been allowed to sit for 30 minutes. Lightweight items such as bottle caps should be glued down to prevent floating.
Embedding Fragile Objects: To embed fragile items specials steps need to be taken. Using a sprayable polyurethane or lacquer clear coat is a great way to seal your object without touching it. Make sure you follow the directions for the sealer and ensure the object is fully cured before coming in contact with the epoxy.
Thick Build-Ups: This product can be used to build up unlimited depths. Each flood coat should not exceed 1/8”. Attempting to pour thicker can cause the epoxy to generate excessive heat which in turn will cause more air bubbles, possibly cracking and shrinkage. It is advisable to wait at least 4 hours between pours to allow sufficient curing and cooling.
Damming The Edges: We recommend allowing the epoxy to run over the edges of your surface as it will self-level at approximately 1/8” at a time. If your application calls for a temporary dam to be constructed, it must be done with great care to guarantee it can be removed after the epoxy is cured. Ideally, a smooth, soft or flexible plastic strip should be used because the epoxy will not stick to it. Alternatively, wooden trim can be used but only if it is first covered with a 2 to 4 mil plastic sheeting. Lining the wood trim with the plastic and tacking it to the edge should prevent the epoxy from running in between the edge and the plastic. Testing on a small mock-up should be done to ensure no leakage or problems will occur with your damming technique.
*Some very aged and kiln dried woods may need multiple seal coats to prevent air from escaping them. It is not uncommon for as many as 3 seal coats to be used on aged and kiln dried woods.
*If at any time you need help with advanced techniques, please reach out to us directly. We are always here to help
No comments:
Post a Comment